Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - Davew

Pages: [1] 2 3 ... 7
Technical Advice and Questions / Re: T150 Rebuild question
« on: December 09, 2013, 01:14:38 pm »
put the synchronizers in neutral and spin input shaft , the output shaft shound not spin .
put the synchro in reverse spin input shaft clockwise and output shaft should turn counter clockwise.

Work In Progress / Re: Jenn's 47 CJ2A!!!!
« on: December 01, 2013, 09:13:12 am »

Work In Progress / Re: Jenn's 47 CJ2A!!!!
« on: November 30, 2013, 09:18:28 am »
This is a video of it running for the first time since reassembly.

Work In Progress / Re: Jenn's 47 CJ2A!!!!
« on: November 30, 2013, 09:14:46 am »

and this it where it it now. lots left to do before paint.

Work In Progress / Re: Jenn's 47 CJ2A!!!!
« on: November 30, 2013, 08:31:02 am »
Well finally will update with pics. I dont have many tech pics of this build. I just dont pause to take any.It's just progress stuff. I just looked through and Jenn deleted all the pics, so I will start from the beginning.

Work In Progress / Re: Jenn's 47 CJ2A!!!!
« on: November 06, 2013, 06:04:06 pm »
Well no pics yet , but the rolling chassis is only a couple wires away from starting and driving.Once I know everything works The tub will be going on for final mock up and body work. Than the tub will be taken off again and get painted.

Work In Progress / Re: Colli Goes Commando
« on: November 06, 2013, 05:58:42 pm »
Way cool . Cant wait to see it out on the trail. hahaha. Great progress!

General Discussion / Re: PA Jeeps has another National STAR in the club!!!!
« on: November 06, 2013, 05:26:03 pm »
Too cool. if I am not mistaken I think that is Jenns Jeep on the other page.

General Discussion / Re: Ballpeen Racing Build thread ??
« on: January 29, 2013, 09:03:02 am »
Lots of good Tech stuff in that. Wasted

General Discussion / Ballpeen Racing Build thread ??
« on: January 28, 2013, 09:17:54 am »
will some one point me in a direction for that. I can not find it using the "search"  I hope it didnt get deleted it had a wealth of info and ideas in it.

Monthly Meetings / Information / Re: January Newsletter
« on: January 08, 2013, 07:35:39 pm »
Most excellent new letter.

General Discussion / Re: Sad News
« on: December 31, 2011, 09:34:37 am »
R.I.P. hopefully others can learn from this tragedy .

Work In Progress / Re: Jenn's 47 CJ2A!!!!
« on: December 29, 2011, 10:58:47 am »
I steam cleaned it first, than used a wire wheel on a hand held grinder. Sand blasted the joints, seams and hard too get too spots. Wiped it down with metal prep than used a self etching primer than paint.

Work In Progress / Re: Jenn's 47 CJ2A!!!!
« on: December 27, 2011, 06:25:40 am »
That is plain old, brush on rustoleum. Satin black. You can't see any brush marks. I decided to use this instead of powder coat or pors and epoxy frame paint because it's the easy to repair if it gets scratched. Just scuff it up slap on more paint and its good to go.

jim unplug the fuel sender at the fuel tank and turn key on the gauge should go to full or passed. If it does the sending unit is bad and you gotta drop the tank. If the gauge stays at empty the gauge is faulty.

Pages: [1] 2 3 ... 7