1
Wanted - Jeep Related / Re: WTB: 26 Spline 1310 CV yoke for a Dana 20 / Dana 300
« on: September 24, 2015, 02:41:49 pm »
If you're putting it on the rear, the yoke from a 231 will work. May have some clearance issues on the front.
News:
FORUM ACCOUNT REQUESTS
If you receive a "denial" email...Reply to: president@pajeeps.org with the following:
User Name: Password: Email Address:
We'll gladly create you an account manually.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
PA Jeeps Club Events / Re: All Blacks Trail Ride
« on: September 24, 2015, 02:34:08 pm »
Planning on attending. If we go to AOAA I might be able to find some trails that are blackish.
3
General Discussion / Re: 4.2 to 4.0 motor swap information:
« on: November 22, 2012, 11:27:13 am »
You could put the intake and carb on the 4.0. Would help cut cost and down time. Will need to slighty modify the intake but it does'nt take very long. If you use the distributor from the 4.2 it will be a bolt in and run. I'm not saying it is the best use of a 4.0, but it is easy and cheap. Jim
5
PA Jeeps Club Events / Re: Snow Shoe Trip
« on: October 18, 2011, 06:46:30 am »
This is Grady. I don't have an account for Pa Jeeps yet. I am using my dad's just to give a big thanks to everyone who came out for my senior project. Everything went great (other than the rain). Thanks to the great turn out I managed to raise $763 for Make a Wish Foundation. Hope to see you all at "No Roads Necessary" in November! Thanks again everyone!
6
PA Jeeps Club Events / Re: Jeep Show Banquet
« on: August 03, 2011, 08:32:50 pm »
Jonni, Grady and I will be there.
7
PA Jeeps Club Events / Re: April all blacks all day
« on: April 25, 2011, 05:31:11 am »
Had a lot of fun even with the front axle rebuild demonstration. Thanks Jenn for guiding. Thanks everyone for your help and I look forward to wheeling with you all in the future.
P.S. All but one had to go around the last obstacle.
P.S. All but one had to go around the last obstacle.
9
Technical Advice and Questions / Re: dana 300 wont seal
« on: April 13, 2011, 07:46:59 am »
Have you filled it on the bench to see where it's leaking? Might help to figure out how to stop it.
10
PA Jeeps Club Events / Re: April all blacks all day
« on: March 23, 2011, 09:25:14 am »
I would be in for the 23rd.
11
Technical Advice and Questions / Re: looking for a good cb radio
« on: February 12, 2011, 07:22:34 pm »
If the only problem is it not allowing you to transmit then it may be your mic. I'd borrow a buddy's mic and plug in and check that first.
12
Technical Advice and Questions / Re: Need some opinions
« on: December 29, 2009, 08:23:26 pm »
SOA is the best mod I ever did to my YJ. My opinion is to remove the body lift go soa and extend the sway bar. Axle wrap will happen but I'm sure you can make an antiwrap bar. Also I've found that limiting the up travel helps with body roll in the turns. I agree with keeping the cog as low as possible but if you use stock springs it will sit low enough. My jeep doesn't see a lot of road miles (3000-4000) a year, but I think it rides better now than it did before. Steering and braking take a little getting used to but there is give and take I guess. Jim
13
Technical Advice and Questions / Re: Transmission choices
« on: November 19, 2009, 05:47:24 pm »
TF727. Not sure on the model of transfer case that has the same spline count as the Dana 300 but there is one that is a direct bolt on.
14
Regional Issues / Re: Deadline for DCNR recreation public input is on Monday July 20!
« on: July 15, 2009, 07:47:49 pm »
Thanks Dave. I would have missed it! Jim
15
Technical Advice and Questions / Re: Trouble shooting
« on: February 12, 2008, 04:34:39 pm »
Sounds like the ignition module. Drivers side fender under the coolant recovery bottle. Jim
Pages: [1]